How To Repair Delonghi Convection Toaster Oven

Toaster ovens are great, when they work. One morning, my Delonghi EO1238 stopped working. No lights, no heat, nothing (except the pronounced timer ticking) – it was if the unit of measurement was unplugged from the wall. A quick check and yes it was plugged in. Check the outlet to make sure a circuit breaker didn't trip and yeah the outlet was working too.

What to do? Here's some quick options… 1) Throw this one away and buy a new ane – but I just got this one a yr or then ago and I don't have an extra $60-$100 lying effectually for a new one. ii) Get without toasted bagels – simply I really similar toasted bagels. Or 3) Repair it. I hateful really, how difficult could toaster oven repair it be?

I did a quick search on the 'net for a crusade based on the symptoms: no power, no light, no estrus, timer still make a ticking racket and it looks like a diddled thermal fuse (NTE 8167) will be the culprit. A call to the local electronics store and they have the part in stock for $0.96 cents! This would probably cost $50 or more than to accept it fixed in a service centre. After my search, I discovered that there are just a few problems toaster ovens confront:

• Blown fuse = no power or lights at all.
• Bad timer = the unit volition not shut off automatically.
• Bad thermostat = unregulated heat or no heat.
• Tray/door won't close = check the tray is correctly installed or no debris blocking door.

That'due south about it. There'south not much to go wrong, so fixing toaster ovens should exist simple.

Hither are my detailed steps to ready the Delonghi EO1238 Toaster Oven. This guide will probably work for fixing the Delonghi EO1200, Delonghi EO1251, Delonghi EO1258, and Delonghi EO1260 toaster oven models too as a general guide for fixing any toaster oven - they are actually that elementary.

Toaster oven repair is an easy 'practise it yourself' project. This project will take virtually 30 minutes; I would rate this a 3 on a scale of one to ten for difficulty, and it will easily salvage you $50 dollars or more! If this helps you, at that place is a note on the bottom of this postal service on how you can say "Thanks!"

The tools for this are fairly mutual and if you don't have them they are available for just a few dollars at the local store. Here are the tools and parts you lot will need for this project:

• Phillips Head Screwdriver
• Regular Pliers
• Needle Nose Pliers with Wire Cutter - if you don't have a wire cutter don't worry.
• T20 Torx Commuter – Torx rhymes with forks!
• 1 – NTE 8167 Thermal Fuse. You can get this from Newark Part #06M7505, Mouser Office #526-NTE8167, Halted Part #18164 or any local electronics parts shop.

Now, a Discussion OF Warning: I am NOT an electric service technician or any type of repair person at all. My data is for provided for EDUCATIONAL PURPOSES ONLY. By standing, you implicitly agree to concord me harmless (indemnify me) for whatever loss, damage, or legal liability that may result by you lot continuing with this project. ONLY a professional person should attempt to repair eclectic and/or electronic equipment. If you try this at home and you go injure (or worse) or if it doesn't work – I am sorry, merely I told you only professionals should effort electronic repair.

Now that that's said and out of the way and you still want to proceed, I recommend that you cheque and Brand SURE that you lot have unplugged the toaster oven from the wall. Working on whatever electric apparatus while continued to a power source could KILL You. And so double cheque this ane.

ane. Remove the Side Panel on the Control Side of the Toaster Oven.

You volition need to remove the gray plastic side console to proceeds access to the fuse.

This cover is held in identify past ii (2) Torx screws located on the dorsum of the unit and

a single (1) Phillips Head spiral on the bottom near the forepart of the toaster oven.

These 3 (3) screws are the only ones you will need to remove.

What are Torx screws anyway? Torx screws are specially designed "safety/tamper proof" screws that have a six bespeak star blueprint and are commonly used in consumer electronics assembly. You tin option up a Torx driver at the electronics store where you lot purchased the NTE 8167 fuse. If they don't accept information technology, try Frys, Radio Shack, Home Depot, Lowes, Sears – you lot go the idea.

Once you have the screws removed, the side panel tin can be removed by slightly plying the encompass away from the oven and then pulling the cover towards the rear of the oven.

The side console has three guides that fit into slots on the superlative of the over that you lot want to disengage without breaking.

Don't worry, the side console is fairly sturdy and so I don't call back you lot will pause it only I want yous to exist enlightened virtually the tabs that concur information technology in place.

2. Locating the Thermal Fuse.

With the toaster oven on its side, the thermal fuse is located virtually the acme of the toaster oven in a protective plastic tube and connected to a blackness wire.

The fuse is held in place by bracket clamp secured by a nut.

Yous will need to loosen this nut then that the fuse and attached wire can be slide through the bracket clamp.

This was tough for me, just I discovered a fiddling crook! The head of the screw that the nut is attached to is available inside the oven. You lot could use your Pliers to hold the nut while yous take your Phillips Head screwdriver and loosen it from the within. I didn't discover this until I was putting everything back together.

Once the nut is loose, take your Needle Olfactory organ pliers and remove the lead and black wire attached to the timer machinery.

At present that the lead wire is removed from the timer machinery, yous can slide the wire through the clench and gain admission to the fuse.

Slide the protective plastic tube back downwardly the wire to expose the fuse.

Yous should have admission to the fuse like to this.

iii. Replacing the Thermal Fuse

Now that you lot accept access to the fuse, you tin can try and pry loose the crimped metallic connectors that attach the fuse to the black wire. These are factory crimped connectors and mine were impossible so I had to cut the wire to remove the fuse.

Before y'all cut the wire, brand certain your new fuse includes new metal connectors (mine did). If you have to cut the wire, cutting information technology on the outside of the connector (opposite side of the fuse) simply every bit close to the connector as possible. Do this for both sides of the fuse. This will go out you plenty of remaining wire to piece of work with.

At present that the fuse has been removed, you volition need to install a new fuse.

If you cut the wire, you volition need to trim the wire back for a new connexion. Use your Needle Olfactory organ pliers with wire trimmer (or whatsoever pocketknife, razor bract, X-Acto knife, etc) and trim the wire.

Only remove enough wire to fit into the new connector – cypher more than.

Once the wire is trimmed and ready:

1. Slide a new connector over the wire and and so
2. Slide the wire from the fuse into the connector
3. At present take your pliers and crimp the connector. The connector will shrink easily and securely bring together the 2 wires.

You will need to do this for both sides of the fuse – merely make sure you withal have the protective plastic cover on the wire!

Now that both sides of the fuse accept been joined to the black wire, slide the protective plastic tube back over the fuse.

4. Re-Assembly.

It's time to put everything back together. Only follow the instructions in opposite and everything will be finished soon:

• Start with sliding the wire through the clench.
• Reattach the black wire's lead to the timer.
• One time the lead is fastened, make certain the protective plastic cover is slide back into the clamp. Once yous accept it where y'all want it – tighten the clamp. It doesn't need to be difficult tight – just snug enough to prevent the blackness wire from moving.
• Put the side cover back on the unit. Start by aligning the three tabs on the summit, slide the cover forward, and pop back into place.
• Install the bottom Phillips Head screw.
• Install the 2 (2) rear Torx screws.

Once everything is reassembled, you can plug the toaster back into the outlet. When y'all turn on the toaster oven you will now run across the interior light working and the front reddish indicator lighting. You did it. Congratulations.

Viola– TOAST!

Now brand yourself a prissy cup of coffee and some cinnamon-sugar toast.

If y'all found this tutorial helpful, please consider proverb thank you past leaving a tip for a cup of Joe or some bagels (I'chiliad out)... You tin can click the tip jar image in the upper right hand corner or click here and y'all volition be taken to PayPal to consummate the transaction in total security. Check back oftentimes for other tutorials to fix your stuff.

Thanks.

Source: http://thingsyoucanrepair.blogspot.com/2010/07/delonghi-eo1238-toaster-oven-repair_13.html

Posted by: jenkinscrushe2000.blogspot.com

Share this post